Garage Door Keeps Going Back Up

Your garage door should be secured and functioning well, as it is probably your home’s largest exterior opening. However, problems can eventually happen to any garage door. The most common question homeowners ask is why their garage door keeps going back up immediately after hitting the floor. There are a few reasons why this happens.

Garage Door Keeps Going Back Up

As with any other facility problems at home, there is no single reason why your garage door opens after closing it. If you are experiencing such an issue, check out the following possible causes and some garage door repair tips.

You Need to Replace the Logic Board 

Just like a computer has a motherboard, your garage door also has a logic board. The logic board is your garage door opener’s brain, and even with machines, a brain can wear out over time. A worn-out logic board can cause problems with your garage door, such as closing then opening again and vice versa. When this happens, you may need to replace it.

You Need to Adjust the Limit Switch Garage Door Keeps Going Back Up

Every garage door opener has a limit switch that controls where the door stops when it is lowered or raised. If your garage door won’t close all the way and keeps going back up, you may need to check the settings of your limit switch. You will need a flathead screwdriver to adjust it.

You Need to Adjust the Travel Down Setting 

The travel down setting of your garage door opener controls the distance the garage door has to travel before it completely closes. If it closes before the set distance is met, it may have detected something, so it goes back up to prevent damage or safety threat. However, your garage door components may sometimes contract and change due to weather changes. In this case, the distance may change. So adjusting the travel down setting to a new distance can fix the issue.

You Need to Check for the Presence of Any Blockage

If your garage door is hard to open or reverses immediately after closing, the simplest thing you can do is check the threshold for anything that blocks it. Your garage door will sense even the slightest blockage, which will cause it to go back up to maintain safety and prevent damage.

If, however, the threshold is clear and the other possible causes mentioned above did not fix the issue, it could be a whole other problem. Read the instruction manual of your garage door opener or consult a garage door service professional to help you.

Questions

Why Does My Garage Door Stop and Go Back Up?Garage Door Keeps Going Back Up

A garage door that stops and goes back up is usually due to malfunctioning infrared sensors. If there is such an issue, you can see one of the sensor lights blinking. Malfunctioning sensors can be caused by a blockage, dirty eyes, loose wires, or just bad sensors in general. This causes the transmitters to not function well in closing the garage door.

Why Does My Garage Door Go Up by Itself?

There are a few reasons why a garage door goes up by itself. Sometimes, it is because of a system power surge; other times, you simply need to change your garage door opener’s code. It can also be caused by a rogue signal that interferes with your receiver – a common scenario when a neighbor set up a garage door opener code similar to yours.

Why Will My Garage Door not Stay Down?

The most common cause of a garage door that won’t stay down is off limit settings. As mentioned above, the limit switch dictates the garage door when it is completely open or closed. If you set the down limit too far, it will cause the garage door to think that it has not completely closed when it hits the ground.

To Summarize 

Many homeowners treat their garage door as the main entrance to their house. Because of how frequently garage doors are used, it is essential to maintain it for your safety and security. You may encounter problems from time to time, such as when the garage door keeps going back up while trying to close it. There are a few reasons that can cause it, but if the above tips do not work, our team here at On Track Garage Doors Service can troubleshoot your garage to ensure it doesn’t go back up anymore.

Adjusting Your Garage Door Photo Eye

Adjusting Your Garage Door Photo Eye Phoenix AZ

Today’s garage doors are outfitted with safety precautions. Some of them are part of the leading edge as the garage closes, others are infrared beams which “watch” for people or possessions to be in the garage door’s path.

Today will we talk about the photo eye that controls one type of safety protocol. For the infrared beam to work correctly, the beam must shoot straight at the other sensor and the “eye” must pick up the signal clearly. If they are out of alignment the system will believe there is an vehicle, object, person, or even a pet in the way and it will not close.

These sensors are usually installed about 6 inches off the floor.  If you can’t get your garage to close, there is a chance that the problem is the photo eye. Follow the steps below to get your garage working again.

Photo Eye Adjustment Steps

Step #1 – Knowing your enemy is the biggest part of any repair. Garage doors that will neither open or close are having more problems than misaligned photo eyes. However if your door will not close, or only closes a bit and then retracts, you might check your photo eyes. Some garage doors will not attempt to close if the beam is not hitting right, they might flash a light or make a clicking sound.

Step #2 – Clear the path around the garage door and the sensors. While you would probably notice if the car was hanging out a small item that has fallen in front of the garage door sensor will prevent it from working. In addition if someone has bumped the sensor or something has fallen on it, it will not work correctly.

Step #3 – Check the lights on the sensors. Most sensors will have LED lights installed to help you know their current condition. If one of the sensors light is not on or it is flashing you should try to adjust it. If you aim it just right it should re-establish the connection and allow your garage door to close again. Persistent problems with sensors coming out of adjustment should be looked at by qualified garage door technicians.

Step #4 – Wipe your eyes, or at least clean your sensors. It is easy for rain, dust, or dirt to get onto the lens of your sensors. Using a damp cloth you should wipe the cobwebs, dirt, or dust away from the lens and then ensure they are pointed correctly. This should help you get both LED lights to come on and indicate that they are working properly. There is also a chance that the sun shines into the sensor at certain times of day. If you suspect this, you can have a sun shade installed on your garage door sensor to overcome this problem.

Step #5 – The sensors are installed many times with pivot brackets. These brackets allow the angle of the sensors to be customized and overcome walls or tracks that are out of plumb. If your house is settling or the track has been bent the bracket can be loosened and the sensor pointed back at level to fire directly at the other sensor.

Step #6 – Photo eyes in garage doors should be mounted at exactly the same height. While they might work for a while with a slight difference in height, they will start to have problems over time and be more prone to dysfunction with normal environmental buildup on the sensors.

Step #7 – Checking the wires is the last step in DYI garage door repair. If the wires leading to your sensors are pulled loose or have been frayed you should call for some professional help. Caring for the safety system of your garage door is a job for professionals and you should invest in the safety of you and your family.

Garage Door Photo Eye Service

If you have tried these steps and haven’t been able to get your garage door working, give the experts a call. On Track Garage Door knows all brands and technology to get your garage door back on track. We can help you adjust, repair, or replace damaged photo eye safety sensors on your garage door anywhere in the Phoenix valley. Call today at 480-641-2301.